ASTM F2054 PDF

13 Nov Hold variables constant. Per ASTM F “If correlations between pieces of test equipment are to be made it is important that all. ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. ASTM F Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within Restraining Plates.

Author: Bralkree Fenrikazahn
Country: Belgium
Language: English (Spanish)
Genre: Software
Published (Last): 10 October 2016
Pages: 339
PDF File Size: 14.18 Mb
ePub File Size: 11.35 Mb
ISBN: 547-5-40725-897-3
Downloads: 66464
Price: Free* [*Free Regsitration Required]
Uploader: Kajigal

This test method should be combined with other methods of evaluating overall package sstm, uniformity of the package seal, or opening functionality, if so required.

Typical parameters can include, but are not limited to the package size, material, type and configuration of seal, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine response to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates. See Appendix X2 for further information. Under Test Methods F the stresses are not distributed uniformly asmt all areas of the package seal.

Active view current version of standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

Link to Active This link will always route to the current Active version asgm the standard. Historical Version s – view previous versions of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations.

  LA NOUVELLE COMMUNICATION YVES WINKIN PDF

This standard does not purport to address all of the safety concerns, if any, associated with its use.

In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. Pressure differentials may occur during such processes as sterilization and transportation.

This test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal. Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures. An indicator of the minimum burst strength may be of importance to the package manufacturer and end user in ensuring adequate package integrity.

See Appendix X4 for information. This test method cannot provide a measure of package seal uniformity. Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations.

Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.

Product List | RDM Test Equipment | Assured Quality Testing Solutions

By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the astk, where seals are normally placed. Link to Active This link will always route to the current Active version of the standard.

This test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

  LIVRO AERODINAMICA E TEORIA DE VOO DOWNLOAD

ASTM F2054

Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses. See Appendix X4 for information.

Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the d2054. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses. This allows the test to have a higher probability of detecting the weakest area of the seal and provide a measurement of the pressure required to “burst” open the package.

In particular it is intended as applicable to packages with seals aztm have a peelable seal feature peeled open by end user to remove contents of package. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.