FLUKE 5500A MANUAL PDF

Each Fluke product is warranted to be free from defects in material and The A Manual Set provides complete information for operators and service or. Warning If the A Calibrator is operated in any way not specified by the A Operators Manual or other documentation provided by Fluke, protection. View and Download FLUKE A operator’s manual online. Multi-Product Calibrator. A Test Equipment pdf manual download.

Author: Macage Gagore
Country: Seychelles
Language: English (Spanish)
Genre: Finance
Published (Last): 1 February 2005
Pages: 264
PDF File Size: 11.12 Mb
ePub File Size: 3.59 Mb
ISBN: 865-8-63893-470-7
Downloads: 6954
Price: Free* [*Free Regsitration Required]
Uploader: Mazugis

Page Remote Operation Introduction Flluke The A Calibrator can produce voltages up to V rms and must be programmed with caution to prevent hazardous voltages from being produced without sufficient warning to the operator.

Full text of “FLUKE A SERVICE MANUAL WITH SCHEMATICS”

flyke The equipment setups are different for each band. Compensation is available for capacitances of nf and above. Contact your authorized Fluke sendee center for recycling information. Grasp the top and bottom of the air filter frame. Removing the Keyboard and Accessing the Output Block Using exactly 10 MO, the nominal value is 9.

5500A Operator Manual

The warranty is located at the front of this manual. AC Current, Trianglewave Characteristics typical. R Bad decimal number CME: Since oscilloscope calibration requires many adjustments of the output signal, the three available methods for changing these settings for oscilloscope calibration are summarized below.

  BAGH E FIDAK IN URDU PDF

AC Voltage amplitude Procedure provided in this manual. Page 54 A Operator Manual Operator Manual Serial Connectors The two 9-pin serial connectors on the rear panel of the A Calibrator are used to interface with a computer, or controller, and an instrument serial port.

How to Obtain Parts Once you have turned R44 to the point at which the spur just disappears, the signal is balanced between the VCOs and you have completed the adjustment. This is the same as pressing the A Calibrator front panel key. Enter the A reading in Column A of Table This instrument may be susceptible to electro-static discharge ESD from direct contact to the binding posts.

Also See for A Getting started – 46 pages Service manual – pages.

FLUKE 5500A Operator’s Manual

Adi listing Short-Term Edge. Title A Multi-Product Calibrator. Adjust the amplitude using the Calibrator Mainframe front panel knob until the power sensor reading matches the 10 MHz reference within 0.

LCR Meter Connections omf. Test the ac and dc current function: DC Voltage Calibration This procedure uses the following equipment: Harmonics 2 to 50 ,anual At 10 ns, the user can chose between the square wave or the leveled sine signal.

Testing Harmonics Amps Performance Time Marker Function Specifications Leveled Sine Wave Reference Verification.

A Operator Manual

See SC Service information, Specifications, AC current non-sinewaveac current sinewavesAC current sinewaves extended bandwidth. Input Impedance Mode Capacitance Capacitance measurement circuits are contained on the A50 SC Scope Option board, utilizing signals from the leveled sine wave source. The blue softkey under Output toggles the impedance between 50 O and 1 MO. Page A Operator Manual Note The entered temperature will be cleared to 0 C 32 F if you change between tc and rtd, or change the type of thermocouple except for a B-type thermocouple, tluke clears to C.

  IEC 60707 PDF

See the Service Manual for more information. This also applies to power outputs. Volts and Current Phase Calibration. Refer to “Checking A Status” for more information.

This is the first of five calibration menus, which you can scroll through by pressing the softkey under MODE. Fluek Time Less than 5 seconds for all functions and ranges except as noted. For this test, set the A manial to sinewave.

If two amplitudes are supplied, the A Calibrator sources two outputs. Calibration Constant Report, Printout Format.

Lift out the Filter PCA. The signal path is also split to drive the external trigger circuitry on the A50 board.