Hewlett-Packard shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in connection with the furnishing or use of this. View and Download HP LaserJet user manual online. LaserJet All in One Printer pdf manual download. Also for: Laserjet m. View and Download HP LaserJet service manual online. LaserJet All in One Printer pdf manual download. Also for: Laserjet m.
|Published (Last):||1 April 2004|
|PDF File Size:||5.27 Mb|
|ePub File Size:||12.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Service Manual – Printer Service Manual – Includes troubleshooting, error messages, paper jams, parts and parts diagrams. The ring for incoming faxes. Page 42 To change the alarm volume The alarm is heard when the device is presenting an alert or critical error message. Internal components 4 of 4 Table Do not try to pull the page out because you may damage the document scanner.
Output roller removal 2 of 2 EN Internal assemblies Note Delivery assembly 1 Remove the output roller see pages 1 1 4 and 1 1 5. Copying tasks The product functions as laserjer standalone copier — you do not have to have software installed or amnual the computer on to make copies.
Also, verify that the guides laaerjet not adjusted too tightly or too loosely against the paper.
Flip pages up portrait – This layout is often used with clipboards. Verify that the pins are not dirty or corroded and that the spring-loading action is functional. Use the Page Setup dialog box to set the page size and orientation for the new cover sheet. The fax line to which you were Allow the product to retry sending! Cancel all the pages that fit into memory will fax jobs or clear the faxes from be printed.
Problem Cause Solution The product is The product is malfunctioning.
The toner cartridge was improperly installed. The paper was poorly cut by the manufacturer and is sticking together.
Pad – Separation pad – Separation pad and holder arm. Printer motor does not 1. They also provide graphics of the product to help identify the different external hardware parts. Once the faxes are sent, detected unsent faxes and will try the product will return to the to resend them. Paserjet might be printing on the wrong side of the media.
Gear train motor 1 of 3 Chapter 5 – Removal and replacement EN Note 3 Remove the four screws callout 1 securing the metal plate over the gear train, and very gently release it. Inserting A Pause Or Wait Into A Fax Number Inserting a pause or wait into a fax number You can insert pauses into a fax number you are dialing or programming to a one-touch key, speed-dial code, or group-dial code.
Because the beam is sweeping the entire length of the drum and the drum is rotating, the entire surface area of the drum can be covered. The printer door was opened while a job was printing. This interface provides high speed and two-way communication between the printer and the host, allowing the user to change printer settings and monitor printer status from the host computer.
Perform the high-voltage power supply check see page Document scanner path 64 Figure 9. Plug the product phone cord into a jack for another phone manuxl. Then, clear the document feeder tray. Verify that the motor connector J1 is seated into the ECU.
Clearing jams from the scanner path area Use the following procedure to clear jams from the scanner area To clear jams from the scanner path area Using both hands, pull the document release door control panel toward you. Sending Faxes To One Recipient Sending faxes to one recipient This procedure details how to send a fax to one recipient.
The specification laseruet maximum paper curl when the paper is lying flat before print is 0. Verify that the motor is correctly mounted to the printer chassis. Make sure that the media meets HP’s specifications.
Solenoid removal 3 Release the solenoid. General printing problems Use the table in this section to solve printing problems. Page The product is A sensor may not be operating properly. Changing Answer Ring Patterns Changing answer ring patterns If you subscribe to ring pattern service with your telephone company, enable the product jp detect ring patterns.
Stopping A Print Job Set the correct margins, paper size, and orientation in your software. The original is on colored paper. Make sure you removed the entire lasedjet of the sealing tape from the toner cartridge before you installed it.
Product Maintenance This section provides the following topics: If the jam is only visible from the front of the front output slot, raise the front cover part way with one hand. The product deleted the incomplete received data before attempting to forward the 33200 data. Note Keep the area in front of 33200 front paper output slot clear so that media can easily exit the slot.
If you don’t know whether the outlet is grounded, check with a qualified electrician. Food and Drug Administration has implemented regulations for laser products manufactured since August 1, To delivery the last page. Hinge – Hinge support assembly – For printer door assembly.
The negatively charged toner is attracted to the discharged exposed, grounded areas of the drum, and repelled from the negatively charged unexposed areas. Feeder – Feeder roller assembly – Includes flags and sensors. Remove some of the sheets. Clean and recalibrate the lasserjet.