Consult International Marine’s Interbond brochure on NauticExpo. Page: 1/2. Consult International Marine’s Interbond – Temperate brochure on NauticExpo. Page: 1/4. A hard wearing, surface tolerant, two pack epoxy primer/finish offering corrosion protection in one coat. A temperate version of Interbond is also available for .

Author: Dazragore Kazigrel
Country: New Zealand
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 18 October 2005
Pages: 70
PDF File Size: 2.74 Mb
ePub File Size: 17.93 Mb
ISBN: 636-8-76146-428-3
Downloads: 69585
Price: Free* [*Free Regsitration Required]
Uploader: Bragul

The Online Boating and Maritime Exhibition. Yes please, I’d like to hear about offers and services. In common with all epoxy based coatings Interbond will exhibit chalking of the film on UV exposure. How it works – 1.

Open the catalog to page 4. There is no detrimental effect on product performance.

For low temperature product data see separate data sheet. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. Interbon of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.

Always mix a complete unit in the proportions supplied. Stated figures for pot interbonnd, drying times and overcoating intervals are for low temperature product. VOC values are typical and are provided for guidance purposes only.

Actual safety measures are dependant on application methods and work environment. MSDS includes information such as melting point, boiling point, and flash point of a hazardous material. Open the catalog to page 2. About Careers Team Contact Us. For temperate product data see separate data sheet.


VOC values are typical and are provided for guidance purposes only. Stripe coating of complex structures is recommended.

Products Marine Coatings Marine chemicals Marine lubricants. Note, all scale must be removed and areas which cannot be prepared adequately by chipping or needle gun should be spot blasted to a minimum standard of Sa2 ISO I have made myself a promise to ensure that employers’ and the public are provided with the necessary knowledge and tools to make their workplaces safer.

Marine Coatings Page 1 of 4 Issue Date: Overcoating information is given for guidance only and is subject to regional variation depending upon When using in cargo holds, consult the Interbond Cargo These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Complete a full risk assessment for your workplace so that you can map out all the hazards into a single comprehensive COSHH assessment.

Interbond – International Marine – PDF Catalogs | Documentation | Boating Brochures

Use in accordance with the standard Worldwide Marine Specifications. Petersburg, Russia, phone: Apply in good weather. For temperate product data see separate data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Interbond low temperature grade is not suitable for use in Ballast Holds. When used as part of an approved scheme, this material has the following certification: Consult International Paint for acceptable generic types and extent of surface preparation required.


As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

Stripe coating of complex structures is recommended. This product may be applied as a full coat over most generic types of paint that have been aged for at least 3 months.

Safe handling and storage The right first aid measures Protect people close to you.

Interbond 201 – Low Temperature

Optimum performance is achieved when Interbond is applied over blasted steel. Study the Material safety data sheets for the hazards of the chemical, learn the instructions on handling, storage and interbon emergency measures in case of accident. Consult your International Paint representative for the system best suited for the surfaces to be protected.

Accurate film thickness control is essential, particularly when overcoating existing systems. When spraying large areas, application of a brush coat is recommended over pitted or rough surfaces to ensure full penetration.

There is no detrimental effect on product performance.